Product Specification

Standards Compliance

•

Successfully tested and certified to: EN 795:2012 Type C – 1 users – 5 ft to 60 ft (1.5 m to 18.3 m)

•

Successfully tested to: CEN/TS 16415:2013 – 2 users – 5 ft to 60 ft (1.5 m to 18.3 m)

•

Successfully tested to: GB 38454-2019 坠落防护 水平生命线装置 – 2 Users – 5 ft to 60 ft (1.5 m to 18.3 m)

•

OSHA 29 CFR 1910.140/1926.502 – 2 users – 5 ft to 100 ft (1.5 m to 30.5 m)

8 ft (2.4 m) System	60 ft (18.3 m) System	100 ft (30.5 m) System
Max Users: 2 Capacity: 310 lbs (141 kg) per person, including user, tools and clothing Product Weight: 12 lbs (5.5 kg) Max. Length: 8 ft (2.4 m)	Max Users: 2 Capacity: 310 lbs (141 kg) per person, including user, tools and clothing Product Weight: 19.8 lbs (9.0 kg) Max. Length: 60 ft (18.3 m)	Max Users: 2 Capacity: 310 lbs (141 kg) per person, including user, tools and clothing Product Weight: 25.6 lbs (11.6 kg) Max. Length: 100 ft (30.5 m)

Additional Product Design Information:

•

Anchorage arrest load will not exceed 2,460 lbs (11.0 kN) when used in accordance to these instructions.

•

OSHA: Allowing a 2:1 safety factor, end anchorages must be capable of sustaining a force of 5,000 lbs (22.2 kN) without deformation in directions permitted by the system and must be certified by an engineer in writing.

•

EN/GB: Allowing a 2:1 safety factor, end anchorages must be capable of sustaining a force of 22kN without deformation in directions permitted by the system and must be certified by an engineer in writing.

•

To reduce total fall distance place anchorages at the same level or above workers harness attachment point.

•

When using an anchor sling wrapped around vertical columns, ensure the sling is protected from sharp or abrasive edges.

WARNING! 

Follow instructions provided with optional anchor slings to identify correct usage cases. DO NOT use anchor slings for purposes other than those for which they are designed.

Failure to follow this warning can result in serious personal injury or death.

•

The MSA Cable THLL will absorb the force of a fall primarily through the energy absorber and personal shock absorber. Total fall distance will increase as the lifeline span increases and if a second worker is added to the system. The fall clearance diagram in Fall Clearance Charts shows the minimum clearance required between the level of the lifeline and the highest obstacle below the system. The fall clearance values in the diagram do not include allowances for swing fall.

•

Use of non-MSA components, connectors, and subsystems (including, but not limited to, stanchions, anchorage connectors, harnesses, energy absorbing lanyards, PFLs and SRLs) is only allowed with approval from a Qualified Person. The clearance values given in Fall Clearance Charts DO NOT APPLY if non-MSA components, connectors, and subsystems are used. It is the responsibility of the Qualified Person to verify compatibility and strength of all non-MSA components, connectors, and subsystems (including, but not limited to, stanchions, anchorage connectors, harnesses, energy absorbing lanyards, PFLs and SRLs) and provide the minimum clearance requirements.

•

Personal Fall Arrest System must be attached directly to lifeline or bypass shuttle with a locking snaphook or carabiner only. For applications that do not require the use of bypass shuttles, users may attach directly to the lifeline with approved connectors, that require two separate, consecutive and deliberate manual actions to be detached and are compliant with all applicable standards and regulations in the country or region of use. All MSA retractable type fall arrester (RTFA) up to a length of 50 ft (15 m) are compatible for direct use.

•

EN/GB: User to be equipped with personal fall arresting absorber with a maximum dynamic arrest force of 6.0 kN (1,349 lbs).